Hallo,
ein neues Faxproblem mal wieder.
Kurz zum Aufbau:
Wir wollen mit der 3CX Faxe empfangen und diese an Emails der Nebenstellen weiterleiten.
PSTN Patton 4638 3CX Vers. 6 3CX Faxserver Email
Dies hat eine Weile lang wunderbar funktioniert und alle Faxe sind korrekt als angehängtes PDF angekommen.
Seit neuesten kommen aber nur noch 3-4 KB der Seiten an. Sprich wenn ich das PDF öffne, erscheint meist immer nur ein Schnipsel der gesamten Seite. Bei einem mehrseitigen Fax kommt von jeder Seite ein Schnipsel an.
Verändert wurde an den Einstellungen nix deshalb weiss ich auch nicht woran das liegen könnte.
Config:
Patton:
Version: R4.2 2008-03-11 H323 SIP BRI
#
#
# #
# SN4638/5BIS/UI #
# R4.2 2008-03-11 H323 SIP BRI #
# 1970-01-01T01:43:33 #
# SN/00A0BA033937 #
# Generated configuration file #
# #
#
#
cli version 3.20
administrator hvs password *** encrypted
webserver port 80 language en
system
ic voice 0
low-bitrate-codec g729
system
clock-source 1 bri 0 0
profile ppp default
profile call-progress-tone defaultDialtone
play 1 1000 425 0
profile call-progress-tone defaultBusytone
play 1 480 425 -7
pause 2 480
profile call-progress-tone defaultReleasetone
play 1 240 425 -7
pause 2 240
profile call-progress-tone defaultCongestiontone
play 1 240 425 -7
pause 2 240
profile tone-set default
profile voip default
codec 1 g711alaw64k rx-length 20 tx-length 20
fax transmission 1 bypass g711alaw64k
fax transmission 2 relay t38-udp
fax redundancy low-speed 3 high-speed 3
fax volume -8.5
fax dejitter-max-delay 300
profile pstn default
profile sip default
no autonomous-transitioning
profile aaa default
method 1 local
method 2 none
context ip router
interface IF_IP_WAN
ipaddress dhcp
tcp adjust-mss rx mtu
tcp adjust-mss tx mtu
interface IF_IP_LAN
ipaddress 172.28.28.11 255.255.255.0
tcp adjust-mss rx mtu
tcp adjust-mss tx mtu
context ip router
route 0.0.0.0 0.0.0.0 172.28.28.1 0
context cs switch
national-prefix 00
international-prefix 000
routing-table called-e164 RT_ISDN_TO_SIP_0
route T2 dest-interface IF_SIP_0 MP_REM_CLIR
routing-table called-e164 RT_ISDN_TO_SIP_1
route T2 dest-interface IF_SIP_1 MP_REM_CLIR
routing-table called-e164 RT_ISDN_TO_SIP_2
route T2 dest-interface IF_SIP_2 MP_REM_CLIR
routing-table called-e164 RT_ISDN_TO_SIP_3
route T2 dest-interface IF_SIP_3 MP_REM_CLIR
mapping-table calling-pi to calling-e164 MP_REM_CLIR
map restricted to ""
interface isdn IF_ISDN_0
route call dest-table RT_ISDN_TO_SIP_0
interface isdn IF_ISDN_1
route call dest-table RT_ISDN_TO_SIP_1
interface isdn IF_ISDN_2
route call dest-table RT_ISDN_TO_SIP_2
interface isdn IF_ISDN_3
route call dest-table RT_ISDN_TO_SIP_3
interface sip IF_SIP_0
bind gateway GW_SIP_0
service default
route call dest-interface IF_ISDN_0
early-connect
early-disconnect
remote-party-id called-party
address-translation outgoing-call request-uri user-part fix 10000 host-part to-header target-param none
address-translation incoming-call called-e164 request-uri
interface sip IF_SIP_1
bind gateway GW_SIP_1
service default
route call dest-interface IF_ISDN_1
early-connect
early-disconnect
remote-party-id called-party
address-translation outgoing-call request-uri user-part fix 10001 host-part to-header target-param none
address-translation incoming-call called-e164 request-uri
interface sip IF_SIP_2
bind gateway GW_SIP_2
service default
route call dest-interface IF_ISDN_2
early-connect
early-disconnect
remote-party-id called-party
address-translation outgoing-call request-uri user-part fix 10002 host-part to-header target-param none
address-translation incoming-call called-e164 request-uri
interface sip IF_SIP_3
bind gateway GW_SIP_3
service default
route call dest-interface IF_ISDN_3
early-connect
early-disconnect
remote-party-id called-party
address-translation outgoing-call request-uri user-part fix 10003 host-part to-header target-param none
address-translation incoming-call called-e164 request-uri
context cs switch
no shutdown
gateway sip GW_SIP_0
bind interface IF_IP_LAN router
service default
domain 172.28.28.50
defaultserver manual 172.28.28.50 loose-router
registration-lifetime 300
registration manual 172.28.28.50
user 10000 authenticate password LbFCDNv4/Fk= encrypted default register
gateway sip GW_SIP_0
no shutdown
gateway sip GW_SIP_1
call-signaling-port 5062
bind interface IF_IP_LAN router
service default
domain 172.28.28.50
defaultserver manual 172.28.28.50 loose-router
registration-lifetime 300
registration manual 172.28.28.50
user 10001 authenticate password dZ8edXkjFnM= encrypted default register
gateway sip GW_SIP_1
no shutdown
gateway sip GW_SIP_2
call-signaling-port 5064
bind interface IF_IP_LAN router
service default
domain 172.28.28.50
defaultserver manual 172.28.28.50 loose-router
registration-lifetime 300
registration manual 172.28.28.50
user 10002 authenticate password iAaKwKfxX4Q= encrypted default register
gateway sip GW_SIP_2
no shutdown
gateway sip GW_SIP_3
call-signaling-port 5066
bind interface IF_IP_LAN router
service default
domain 172.28.28.50
defaultserver manual 172.28.28.50 loose-router
registration-lifetime 300
registration manual 172.28.28.50
user 10003 authenticate password ySyWxUvSc/c= encrypted default register
gateway sip GW_SIP_3
no shutdown
port ethernet 0 0
medium auto
encapsulation ip
bind interface IF_IP_WAN router
no shutdown
port ethernet 0 1
medium auto
encapsulation ip
bind interface IF_IP_LAN router
no shutdown
port bri 0 0
clock auto
encapsulation q921
q921
protocol pp
uni-side auto
encapsulation q931
q931
protocol dss1
uni-side user
bchan-number-order ascending
encapsulation cc-isdn
bind interface IF_ISDN_0 switch
port bri 0 0
no shutdown
port bri 0 1
clock auto
encapsulation q921
q921
protocol pp
uni-side auto
encapsulation q931
q931
protocol dss1
uni-side user
bchan-number-order ascending
encapsulation cc-isdn
bind interface IF_ISDN_1 switch
port bri 0 1
no shutdown
port bri 0 2
clock auto
encapsulation q921
q921
protocol pp
uni-side auto
encapsulation q931
q931
protocol dss1
uni-side user
bchan-number-order ascending
encapsulation cc-isdn
bind interface IF_ISDN_2 switch
port bri 0 2
no shutdown
port bri 0 3
clock auto
encapsulation q921
q921
protocol pp
uni-side auto
encapsulation q931
q931
protocol dss1
uni-side user
bchan-number-order ascending
encapsulation cc-isdn
bind interface IF_ISDN_3 switch
port bri 0 3
no shutdown
port bri 0 4
clock auto
encapsulation q921
q921
protocol pp
uni-side auto
encapsulation q931
q931
protocol dss1
uni-side net
bchan-number-order ascending
port bri 0 4
shutdown
Mit dieser Standardeinstellung geht es leider auch nicht mehr
profile voip default
codec 1 g711alaw64k rx-length 20 tx-length 20
fax transmission 2 relay t38-udp
3CX ist die Version 6. r664
Bei den DID für die Faxe ist "Alle Anrufe" weiterleiten auf die enstprechenden Nebenstellen eingestellt. Dort sind die Emailadressen hinterlegt.
Viele Grüße
Wompipomp
ein neues Faxproblem mal wieder.
Kurz zum Aufbau:
Wir wollen mit der 3CX Faxe empfangen und diese an Emails der Nebenstellen weiterleiten.
PSTN Patton 4638 3CX Vers. 6 3CX Faxserver Email
Dies hat eine Weile lang wunderbar funktioniert und alle Faxe sind korrekt als angehängtes PDF angekommen.
Seit neuesten kommen aber nur noch 3-4 KB der Seiten an. Sprich wenn ich das PDF öffne, erscheint meist immer nur ein Schnipsel der gesamten Seite. Bei einem mehrseitigen Fax kommt von jeder Seite ein Schnipsel an.
Verändert wurde an den Einstellungen nix deshalb weiss ich auch nicht woran das liegen könnte.
Config:
Patton:
Version: R4.2 2008-03-11 H323 SIP BRI
#
#
# #
# SN4638/5BIS/UI #
# R4.2 2008-03-11 H323 SIP BRI #
# 1970-01-01T01:43:33 #
# SN/00A0BA033937 #
# Generated configuration file #
# #
#
#
cli version 3.20
administrator hvs password *** encrypted
webserver port 80 language en
system
ic voice 0
low-bitrate-codec g729
system
clock-source 1 bri 0 0
profile ppp default
profile call-progress-tone defaultDialtone
play 1 1000 425 0
profile call-progress-tone defaultBusytone
play 1 480 425 -7
pause 2 480
profile call-progress-tone defaultReleasetone
play 1 240 425 -7
pause 2 240
profile call-progress-tone defaultCongestiontone
play 1 240 425 -7
pause 2 240
profile tone-set default
profile voip default
codec 1 g711alaw64k rx-length 20 tx-length 20
fax transmission 1 bypass g711alaw64k
fax transmission 2 relay t38-udp
fax redundancy low-speed 3 high-speed 3
fax volume -8.5
fax dejitter-max-delay 300
profile pstn default
profile sip default
no autonomous-transitioning
profile aaa default
method 1 local
method 2 none
context ip router
interface IF_IP_WAN
ipaddress dhcp
tcp adjust-mss rx mtu
tcp adjust-mss tx mtu
interface IF_IP_LAN
ipaddress 172.28.28.11 255.255.255.0
tcp adjust-mss rx mtu
tcp adjust-mss tx mtu
context ip router
route 0.0.0.0 0.0.0.0 172.28.28.1 0
context cs switch
national-prefix 00
international-prefix 000
routing-table called-e164 RT_ISDN_TO_SIP_0
route T2 dest-interface IF_SIP_0 MP_REM_CLIR
routing-table called-e164 RT_ISDN_TO_SIP_1
route T2 dest-interface IF_SIP_1 MP_REM_CLIR
routing-table called-e164 RT_ISDN_TO_SIP_2
route T2 dest-interface IF_SIP_2 MP_REM_CLIR
routing-table called-e164 RT_ISDN_TO_SIP_3
route T2 dest-interface IF_SIP_3 MP_REM_CLIR
mapping-table calling-pi to calling-e164 MP_REM_CLIR
map restricted to ""
interface isdn IF_ISDN_0
route call dest-table RT_ISDN_TO_SIP_0
interface isdn IF_ISDN_1
route call dest-table RT_ISDN_TO_SIP_1
interface isdn IF_ISDN_2
route call dest-table RT_ISDN_TO_SIP_2
interface isdn IF_ISDN_3
route call dest-table RT_ISDN_TO_SIP_3
interface sip IF_SIP_0
bind gateway GW_SIP_0
service default
route call dest-interface IF_ISDN_0
early-connect
early-disconnect
remote-party-id called-party
address-translation outgoing-call request-uri user-part fix 10000 host-part to-header target-param none
address-translation incoming-call called-e164 request-uri
interface sip IF_SIP_1
bind gateway GW_SIP_1
service default
route call dest-interface IF_ISDN_1
early-connect
early-disconnect
remote-party-id called-party
address-translation outgoing-call request-uri user-part fix 10001 host-part to-header target-param none
address-translation incoming-call called-e164 request-uri
interface sip IF_SIP_2
bind gateway GW_SIP_2
service default
route call dest-interface IF_ISDN_2
early-connect
early-disconnect
remote-party-id called-party
address-translation outgoing-call request-uri user-part fix 10002 host-part to-header target-param none
address-translation incoming-call called-e164 request-uri
interface sip IF_SIP_3
bind gateway GW_SIP_3
service default
route call dest-interface IF_ISDN_3
early-connect
early-disconnect
remote-party-id called-party
address-translation outgoing-call request-uri user-part fix 10003 host-part to-header target-param none
address-translation incoming-call called-e164 request-uri
context cs switch
no shutdown
gateway sip GW_SIP_0
bind interface IF_IP_LAN router
service default
domain 172.28.28.50
defaultserver manual 172.28.28.50 loose-router
registration-lifetime 300
registration manual 172.28.28.50
user 10000 authenticate password LbFCDNv4/Fk= encrypted default register
gateway sip GW_SIP_0
no shutdown
gateway sip GW_SIP_1
call-signaling-port 5062
bind interface IF_IP_LAN router
service default
domain 172.28.28.50
defaultserver manual 172.28.28.50 loose-router
registration-lifetime 300
registration manual 172.28.28.50
user 10001 authenticate password dZ8edXkjFnM= encrypted default register
gateway sip GW_SIP_1
no shutdown
gateway sip GW_SIP_2
call-signaling-port 5064
bind interface IF_IP_LAN router
service default
domain 172.28.28.50
defaultserver manual 172.28.28.50 loose-router
registration-lifetime 300
registration manual 172.28.28.50
user 10002 authenticate password iAaKwKfxX4Q= encrypted default register
gateway sip GW_SIP_2
no shutdown
gateway sip GW_SIP_3
call-signaling-port 5066
bind interface IF_IP_LAN router
service default
domain 172.28.28.50
defaultserver manual 172.28.28.50 loose-router
registration-lifetime 300
registration manual 172.28.28.50
user 10003 authenticate password ySyWxUvSc/c= encrypted default register
gateway sip GW_SIP_3
no shutdown
port ethernet 0 0
medium auto
encapsulation ip
bind interface IF_IP_WAN router
no shutdown
port ethernet 0 1
medium auto
encapsulation ip
bind interface IF_IP_LAN router
no shutdown
port bri 0 0
clock auto
encapsulation q921
q921
protocol pp
uni-side auto
encapsulation q931
q931
protocol dss1
uni-side user
bchan-number-order ascending
encapsulation cc-isdn
bind interface IF_ISDN_0 switch
port bri 0 0
no shutdown
port bri 0 1
clock auto
encapsulation q921
q921
protocol pp
uni-side auto
encapsulation q931
q931
protocol dss1
uni-side user
bchan-number-order ascending
encapsulation cc-isdn
bind interface IF_ISDN_1 switch
port bri 0 1
no shutdown
port bri 0 2
clock auto
encapsulation q921
q921
protocol pp
uni-side auto
encapsulation q931
q931
protocol dss1
uni-side user
bchan-number-order ascending
encapsulation cc-isdn
bind interface IF_ISDN_2 switch
port bri 0 2
no shutdown
port bri 0 3
clock auto
encapsulation q921
q921
protocol pp
uni-side auto
encapsulation q931
q931
protocol dss1
uni-side user
bchan-number-order ascending
encapsulation cc-isdn
bind interface IF_ISDN_3 switch
port bri 0 3
no shutdown
port bri 0 4
clock auto
encapsulation q921
q921
protocol pp
uni-side auto
encapsulation q931
q931
protocol dss1
uni-side net
bchan-number-order ascending
port bri 0 4
shutdown
Mit dieser Standardeinstellung geht es leider auch nicht mehr
profile voip default
codec 1 g711alaw64k rx-length 20 tx-length 20
fax transmission 2 relay t38-udp
3CX ist die Version 6. r664
Bei den DID für die Faxe ist "Alle Anrufe" weiterleiten auf die enstprechenden Nebenstellen eingestellt. Dort sind die Emailadressen hinterlegt.
Viele Grüße
Wompipomp